DPO2012 -- 2-channel, 100MHz

DPO2014 -- 4-channel, 100MHz

DPO2024 -- 4-channel, 200MHz

Adding 16 digital Channels:

MSO2012 -- 2-channel, 100MHz

MSO2014 -- 4-channel, 100MHz

MSO2024 -- 4-channel, 200MHz

Analog Bandwidth (-3 dB)
5mV / div to 1V/div

1 M points

Edge - Positive or negative slope on any channel or front-panel auxiliary input. Coupling includes DC, HF reject, LF reject, and noise reject.

Pulse Width - Trigger on width of positive or negative pulses that are >, <, =, or ≠ to a specified period of time.

Runt - Trigger on a pulse that crosses one threshold but fails to cross a second threshold before crossing the first again.

Logic - Trigger when any logical pattern of channels goes false or stays true for specified period of time. Any input can be used as a clock to look for the pattern on a clock edge. Pattern (AND, NAND) specified for all analog and digital input channels defined as High, Low, or Don’t Care.

Setup and Hold - Trigger on violations of both setup time and hold time between clock and data present on any of the input channels.

Rise/Fall Time - Trigger on pulse edge rates that are faster or slower than specified. Slope may be positive, negative, or either.

Video - Trigger on line number, all lines, odd, even, or all fields on NTSC, PAL, and SECAM video signals.

I²C (Optional) - Trigger on Start, Repeated Start, Stop, Missing ACK, Address (7 or 10 bit), Data, or Address and Data on I²C buses up to 3.4 Mb/s.

SPI (Optional) - Trigger on SS, Idle Time, MOSI, MISO, or MOSI and MISO on SPI buses up to 10.0 Mb/s.

CAN (Optional) - Trigger on Start of Frame, Frame Type (data, remote, error, overload), Identifier (standard or extended), Data, Identifier and Data, End of Frame, Missing ACK, or Bit Stuffing Errors on CAN signals up to 1 Mb/s. Data can be further specified to trigger on ≤, <, =, >, ≥ or ≠ a specific data value. User-adjustable sample point is set to 50% by default.

RS-232/422/485/UART (Optional) - Trigger on Tx start bit, Rx start bit, Tx end of packet, Rx end of packet, Tx data, Rx data, Tx Parity Error, and Rx Parity Error.

LIN (Optional) - Trigger on Sync, Identifier, Data, Identifier and Data, Wakeup Frame, Sleep Frame, or Errors such as Sync Parity or Checksum Errors.

Parallel (available on MSO models only) - Trigger on a parallel bus data value.

Power Source Voltage - 100 to 240 V ±10%

PowerSource Frequency -  

45 to 65 Hz (90 to 264 V)

360 to 440 Hz (100 to 132 V)

Power Consumption - 80 W maximum

Arithmetic – Add, subtract, multiply and divide waveforms.

Cursors - Waveform and Screen

Automatic Measurements - 29, of which up to four can be displayed on screen at any one time. Measurements include Frequency, Period, Delay, Rise Time, Fall Time, Positive Duty Cycle, Negative Duty Cycle, Positive Pulse Width, Negative Pulse Width, Burst Width, Phase, Positive Overshoot, Negative Overshoot, Peak to Peak, Amplitude, High, Low, Max, Min, Mean, Cycle Mean, RMS, Cycle RMS, Positive Pulse Count, Negative Pulse Count, Rising Edge Count, Falling Edge Count, Area, and Cycle Area

Gating - Isolate the specific occurrence within an acquisition to take measurements, using either the screen or waveform cursors.

Model Number 

Description