Flowline Flow Switches
|
 |
F10 Liquid Flow Switch --
The flow switch set point may be adjusted from .04 to 3 fps and is an
excellent choice for a wide range of relatively clean, non-coating or scaling
type liquids. Media examples include hydrochloric acid, lubrication oil
and glycol solutions. The relay or FET output provides a reliable switch
interface with remote devices such as a PLC, SCADA or alarm. The short
sensor is intended for use in pipe sizes from 1/2 inch to 1 1/2 inch; the
long sensor is applied from 2 inches up. |
-
Set point range: 0.04 - 3 fps (0.012 to 0.91 mps)
-
Factory set point: 0.2 fps (0.06 mps)
-
Set point drift : 0.5% of set point
-
Repeatability: ±5% of set point at const. temperature
-
Response time: 1 - 10 seconds
-
Viscosity range: 1 - 300 centipoise
-
Supply voltage: 12 - 36 VDC
-
Consumption: Relay: 70 mA
-
FET: 50 mA
-
Relay rating: 60 VDC/VAC @ 1A
-
FET rating: 36 VDC @ 100 mA
-
Switch output: Selectable, NO or NC states
-
Set point adjustment: Potentiometer
-
Indication: LED for flow status
-
Fluid temperature: F: 32 - 140 degrees C: 0 - 60 degrees
-
Pressure range: 150 psi (10 bar) @ 25 degrees C, derated @ 1.667
psi (0.113 bar) per degrees C above 25 degrees C
-
Sensor material: Polypropylene/Ryton ® or Polyvinylidene Fluoride
-
Sensor rating: NEMA 4X (IP 65)
-
Mounting thread: 3/4" NPT (3/4" G)
-
Mounting gasket: Viton (3/4") metric only
-
Cable type: 8 ft. (2.5 m), 4-wire (relay) or 3-wire (FET), 22 gauge
with ground, shield and PP or PFA jacket
-
CE compliance: EN 50082-2 immunity EN 55011 emission
|
Liquid or Gas Flow Switch Compact Relay Controller
--
This liquid or gas flow switch package offers a complete solution for
low flow pump or process protection. The short sensor is intended for use
in pipe or ducting from 1/2 inch to 1 1/2 inches; the long sensor is applied
from 2 inches up. The FET output provides a reliable switch interface with
remote devices such as a PLC, SCADA or alarm. Each assembly includes a
compact junction box and flow switch. To complete your product, select
the appropriate liquid or gas sensor configuration, sensor length, material
and output for your application. |
|
Liquid or Gas Flow Switch Compact Junction Box --
| This liquid or gas flow switch package offers a complete
solution for low flow pump or process protection. The short sensor is intended
for use in pipe or ducting from 1/2 inch to 1 1/2 inches; the long sensor
is applied from 2 inches up. The FET output provides a reliable switch
interface with remote devices such as a PLC, SCADA or alarm. Each assembly
includes a compact junction box and flow switch. To complete your product,
select the appropriate liquid or gas sensor configuration, sensor length,
material and output for your application. |
|
G10 Gas Flow Switch --
The flow switch set point may be adjusted from 1 to 90 fps and is an
excellent choice for a wide range of relatively clean, non-coating type
gases. Media examples include air, chlorine gas, nitrogen gas and
process exhaust fumes. The relay or FET output provides a reliable
switch interface with remote devices such as a PLC, SCADA or alarm.
The short sensor is intended for use in ducting sizes from 1/2 inch to
1 1/2 inch; the long sensor is applied from 2 inches up. |
-
Set point range: 1 - 90 fps (0.3 to 27 mps)
-
Factory set point: 10 fps (3 mps)
-
Set point drift : 0.5% of set point
-
Repeatability: ±5% of set point at const. temperature
-
Response time: 1-10 seconds
-
Supply voltage: 12 - 36 VDC
-
Consumption: Relay: 70 mA
-
FET: 50 mA
-
Relay rating: 60 VDC/VAC @ 1A
-
FET rating: 36 VDC @ 100 mA
-
Switch output: Selectable, NO or NC states
-
Set point adjustment: Potentiometer
-
Indication: LED for flow status
-
Fluid temperature:
-
F: 32 degrees - 140 degrees
-
C: 0 degrees - 60 degrees
-
Pressure range: 150 psi (10 bar) @ 25 degrees C, derated @ 1.667
psi (0.113 bar) per degree C above 25 degrees C.
-
Sensor material: Polypropylene/Ryton® or Polyvinylidene Fluoride
-
Sensor rating: NEMA 4X (IP 65)
-
Mounting thread: 3/4" NPT (3/4" G)
-
Mounting gasket: Viton (3/4") metric only
-
Cable type: 8 ft. (2.5 m), 4-wire (relay) or 3-wire (FET), 22 gauge
with ground, shield and
-
PP or PFA jacket
-
CE compliance: EN 50082-2 immunity
-
EN 55011 emission
|
|
